Boost Tracer Manuel d'instructions

Tracer-BN Series —— Maximum Power Point Tracking Solar Charge Controller Thank you very much for selecting our product! This manual offers

7 4 Operation 4.1 MPPT Technology The Tracer-BN series utilizes Maximum Power Point Tracking technology to extract maximum power from the solar modul

8 Current VS. Voltage in 12V system Output power in 12V system Figure 4-1 Nominal 12V Solar Module I-V curve and output power grap

9 Figure 4-2 Tracer-BN series MPPT charging algorithm ·Bulk Charge In this stage, the battery voltage has not yet reached boost voltage and 100%

10 maintain the battery at the Float setpoint. Should the battery voltage remains below the boost reconnect charging voltage, the controller will

11 4.3 LED Indications Charging Indicator Battery Indicator  Charging Indicator Charging LED indicator Ta

12 4.4 Setting Operation Three methods to configure the controller: 1–Remote meter, MT50/MT100 (Use standard twisted net cable, model: CC-RS485-RS4

13 WARNING: Do not use the standard twisted-net cable to connect the device and PC net interface, or the permanent damage will occur. •Load Set Mode

14 5 Protections, Troubleshooting and Maintenance 5.1 Protection ·PV Array Short Circuit When PV short circuit occurs, the controller will stop charg

15 discharging at the default temperature 25℃ to prevent the battery damaged from overcharging or over discharged. ·Over Temperature Protection If

16 NOTE: If all the led are off, please check the voltage of battery. At least 9V voltage to activate the controller. NOTE: If the charging led is

Tracer- BN Series —— Maximum Power Point Tracking Solar Charge Controller Model: Tracer1215BN/Tracer2215BN Tracer3215BN/Tracer4215BN **Array volta

17 6 Warranty The Tracer-BN Series charge controller is warranted to be free from defects for a period of TWO (2) years from the date of shipment to

18 7 Technical Specifications • Electrical Parameters Table 7-1 Description Parameter Nominal system voltage 12VDC / 24VDC Auto work Rated charge cu

19 • Control Parameters Table 7-2 Battery charging setting Gel Sealed Flooded User Over Voltage Disconnect Voltage 16.0V 16.0V 16.0V 9~17V Charging

20 • Environmental Parameters Table 7-3 Environmental Parameter Ambient temperature range -35℃to +55℃ Storage temperature range -35℃ to +80℃ Humidit

21 • Mechanical Parameters (Tracer3215BN) Table 7-6 Mechanical Parameter Dimension 280.7mm x 159.7mm x 60mm Mounting dimension Detail in dimensions

PV Power — Conversion Efficiency Curve Tracer1215BN Illumination Intensity: 1000W/m2 Temp: 25ºC 1. Solar Module MPP Voltage(16.5V, 34V, 66

Tracer2215BN Illumination Intensity: 1000W/ m2 Temp: 25ºC 1. Solar Module MPP Voltage(16.5V, 33V, 66V) / Nominal System Voltage(12V) 2. So

Tracer3215BN Illumination Intensity: 1000W/ m2 Temp: 25ºC 1. Solar Module MPP Voltage(16.5V, 33V, 66V) / Nominal System Voltage(12V) 2. So

Tracer4215BN Illumination Intensity: 1000W/ m2 Temp: 25ºC 1. Solar Module MPP Voltage(16.5V, 33V, 66V) / Nominal System Voltage(12V) 2. So

Tracer1215BN Dimensions (mm)

Contents 1 Important Safety Information ... 1 2 General Information

Tracer2215BN Dimensions (mm)

Tracer3215BN Dimensions (mm)

Tracer4215BN Dimensions (mm)

Version number: V1.7

BEIJING EPSOLAR TECHNOLOGY CO., LTD. Tel: +86-10-82894112 / 82894962 Fax: +86-10-82894882 E-mail: [email protected] Website: http://

1 1 Important Safety Information Save These Instructions This manual contains important safety, installation and operating instructions for Tracer-BN

2 2 General Information 2.1 Overview Thank you for selecting the Tracer-BN series controller which represents advanced technology of our company. The

3 Figure 2-1 Tracer-BN Series Characteristics 1 – Heat Sink Cast aluminum heat sink to dissipate controller heat. 2 – Charging LED Indicator Indica

4 3 – Battery LED Indicator Show charging status. 4 – Key Switch the load on/off in the manual mode and clear the part of faults. 5 –Temperature Se

5 3 Installation Instructions 3.1 General Installation Notes Be very careful when working with batteries. Wear eye protection. Have fresh water avai

6 3.2 Mounting 1. Connect components to the charge controller in the sequence as shown above and pay much attention to the ―+‖ (Red) and ―-‖ (Black)